MULTI-BAND RTK / BASE + ROVER
Emlid Reach RS3 — Multi-Band RTK Surveying with Tilt Compensation
Reach RS3 is a multi-band RTK GNSS receiver for base and rover operation, with IMU tilt compensation up to 60°, Emlid Flow surveying and RINEX logging. It suits general survey, construction and mapping teams whose requirements align with its 184-channel L1/L2/L5 platform.

Observed data, configuration and quality evidence remain attached through handover.
01 / PRACTICAL OVERVIEW
Where Reach RS3 fits in the working system.
RS3 supports point collection, stakeout and independent base/rover configurations. Tilt compensation helps surveyors observe corners, drains, fences and other features without holding the pole perfectly vertical, provided the recommended tilt procedure and field checks are followed.
RS3 remains a practical option, but it is not technically interchangeable with the newer all-band RS4 range. Purchasers working regularly in difficult GNSS environments should compare tracking, correction links, physical protection and workflow requirements rather than relying on a shared nominal accuracy specification.
02 / KEY CAPABILITIES
General surveying with flexible operating roles.
- GNSS
- 184-channel multi-band reception across L1/L2/L5 signals listed in current manufacturer documentation.
- Tilt compensation
- IMU-based tilt compensation up to 60° under supported operating conditions.
- Base and rover
- Supports both roles for appropriate RTK and post-processed configurations.
- Correction connectivity
- NTRIP, LoRa corrections and compatible UHF reception. The current comparison identifies UHF as receive-only on RS3.
- Field software and logging
- Emlid Flow survey and stakeout workflows, with RINEX raw-data logging.
- Physical specification
- 950 g, IP67 protection and up to 18 hours in rover operation under manufacturer conditions.
- Radio
- Integrated LoRa specified at 0.1 W in the current manufacturer comparison. Radio use must suit the exact configuration and applicable local requirements.
03 / BEST-SUITED WORK
A practical tool for established survey routines.
General land surveying
Collect site features and boundary-related observations where professional scope, control and field methodology are properly defined.
Construction measurement
Observe site points, check works and record as-built features with suitable independent checks.
Point, line and setting-out work
Use Emlid Flow projects, codes and design geometry for routine field operations.
Small and medium survey crews
Deploy base/rover or network-rover arrangements according to coverage, staffing and equipment strategy.
04 / TILT-AWARE FIELD METHOD
Make the observation repeatable.
01 / Prepare
Check firmware, Flow settings, pole height, correction input and coordinate reference before use.
02 / Initialise tilt
Follow the manufacturer’s current initialisation and operating procedure rather than assuming tilt is always active.
03 / Occupy and observe
Keep the pole tip at the intended point, avoid unstable placement and record appropriate solution information.
04 / Check
Repeat critical observations and compare known points. Investigate discrepancies instead of averaging them away without explanation.
05 / RS3 OR RS4?
Compare capabilities, not just nominal precision.
| Specification | Reach RS3 | Reach RS4 |
|---|---|---|
| GNSS class / channels | Multi-band / 184 | All-band / 672 |
| Tilt compensation | Up to 60° | Yes; current RS4 tilt workflow |
| Base and rover | Both | Both |
| IP protection | IP67 | IP68 |
| Battery | Up to 18 h | Up to 16 h |
| Weight | 950 g | 927 g |
| Selection emphasis | General multi-band survey and setting out | Newer all-band professional base/rover workflow |
06 / PROCUREMENT NOTE
Evaluate the whole operating environment.
A nominal RTK specification does not mean every receiver performs identically under canopy, beside structures or around reflective surfaces. Test representative conditions where those environments are routine, and record fixed, float and single solution behaviour rather than reporting only successful points.
Easepect can arrange a comparison demonstration, scope base accessories and correction options, and document a field procedure for your team. Existing older Reach models can be discussed as legacy/support arrangements, not presented as the current flagship range.
07 / FREQUENTLY ASKED QUESTIONS
Before choosing Reach RS3.
General multi-band surveying, construction measurement, point and line collection, setting out, control observations and independent base/rover work where its capabilities meet the project requirements.
RS3 is a 184-channel multi-band receiver with IP67 protection and up to 18 hours of rover battery life. RS4 is a 672-channel all-band receiver with IP68 protection and up to 16 hours. Both support base/rover roles and tilt, but field performance should be evaluated by environment.
The current comparison describes RS3 UHF as receive-only. Confirm the exact required radio arrangement; do not assume that UHF reception means UHF base transmission.
No. RS3 specifies tilt compensation up to 60° under supported conditions. Follow the current initialisation and observation procedure and verify critical measurements independently.
Yes, this microsite presents RS3 alongside RS4 Pro, RS4 and RX2 as the four primary pole/rover receivers. RS2+, original RX and other older models are treated only as legacy/support topics.
LOCAL IMPLEMENTATION / SINGAPORE
Not sure which Emlid receiver suits your project?
Tell us what you are surveying, your operating environment and required deliverables. Model selection is optional; Easepect can help identify a suitable hardware and software workflow.